這是什么意思？？？？
GXLX:BL1:9ac50e:4a8da0;FEAT:ADFD318C:0;POC:3;RCY:0;EMMC:0;READ:0;CHK:BF;READ:0;0.0;CHK:0;
TE: 1361700
BL2 Built : 14:48:45, Sep 26 2018.
gxl g6d68897 - yao.zhang@droid07
Board ID = 7, adc=557
set vcck to 1070 mv
set vddee to 1070 mv
CPU clk: 1200MHz
DDR3
DDR3 chl: Rank0 @ 792MHz
bist_test rank: 0 26 00 4c 39 19 59 21 00 43 3e 1e 5f 23 00 46 40 20 60 21 00 42 3d 1c 5e 631
Rank0: 1024MB(auto)-2T-11
AddrBus test pass!
-s
Load fip header from eMMC, src: 0x0000c200, des: 0x01400000, size: 0x00004000
New fip structure!
Load bl30 from eMMC, src: 0x00010200, des: 0x013c0000, size: 0x00007600
Load bl301 from eMMC, src: 0x00018200, des: 0x01380000, size: 0x00002200
Load bl31 from eMMC, src: 0x0001c200, des: 0x10100000, size: 0x00019600
Load bl33 from eMMC, src: 0x00038200, des: 0x01000000, size: 0x00047000
NOTICE: BL3-1: v1.0(debug):3048f05
NOTICE: BL3-1: Built : 22:38:14, Aug 20 2017
NOTICE: BL31: GXL normal boot!
NOTICE: BL31: BL33 decompress pass
[Image: gxl_v1.1.3103-9234004 2019-01-28 13:26:52 sunny.luo@droid06-sz]
efuse init ops = c1
efuse init hdcp = c, cf9=7
x2_hp_e = 0
bl30: check_permit, count is 1
bl30: check_permit: ok!
chipid: 0 0 3 c c 0 56 b3 b0 a0 0 c1 not ES chip
[1.723993 Inits done]
INFsO: BL3-1: Initializing runtime services
WARNING: No OPTEE provided by BL2 boot loader
ERROR: Error initializing runtime service opteed_fast
INFO: BL3-1: Preparing for EL3 exit to normal world
INFO: BL3-1: Next image address = 0x1000000
INFO: BL3-1: Next image spsr = 0x3c9
rcure task sta
!t
U
a-Bhiogoht t a2sk0 1s5t.a0r1t-!g
alofw4 t5a3s9k- dstiarrtt!y
(Feb 27 2019 - 16:53:20)
DRAM: 1 GiB
Relocation Offset is: 36eef000
register usb cfg[0][1] = 0000000037f61298
[CANVAS]canvas init
vpu: error: vpu: check dts: FDT_ERR_BADMAGIC, load default parameters
vpu: clk_level = 7
vpu: set clk: 666667000Hz, readback: 666660000Hz(0x300)
vpp: vpp_init
MMC: aml_priv->desc_buf = 0x0000000033edfac0
aml_priv->desc_buf = 0x0000000033ee1de0
SDIO Port B: 0, SDIO Port C: 1
emmc/sd response timeout, cmd8, status=0x3ff2800
emmc/sd response timeout, cmd55, status=0x3ff2800
[mmc_init] mmc init success
dtb magic 08088b1f
Amlogic multi-dtb tool
GZIP format, decompress...
Multi dtb detected
unified board, board id = 7
Multi dtb tool version: v2 .
Support 10 dtbs.
aml_dt soc: gxlx platform: p261 variant: 1g
dtb 0 soc: gxbb plat: p201 vari: 1g
dtb 1 soc: gxbb plat: p201 vari: 2g
dtb 2 soc: gxl plat: p211 vari: 1g
dtb 3 soc: gxl plat: p211 vari: 2g
dtb 4 soc: gxl plat: p215 vari: 1g
dtb 5 soc: gxl plat: p215 vari: 2g
dtb 6 soc: gxlx plat: p261 vari: 1g
dtb 7 soc: gxlx plat: p261 vari: 2g
dtb 8 soc: gxlx plat: p265 vari: 1g
dtb 9 soc: gxlx plat: p265 vari: 2g
Find match dtb: 6
start dts,buffer=0000000033ee4610,dt_addr=0000000033ee4610
Amlogic multi-dtb tool
Single dtb detected
parts: 13
00: logo 0000000002000000 1
01: recovery 0000000002000000 1
02: rsv 0000000000800000 1
03: tee 0000000000800000 1
04: crypt 0000000002000000 1
05: misc 0000000002000000 1
06: instaboot 0000000020000000 1
07: boot 0000000002000000 1
08: system 0000000040000000 1
09: cache 0000000020000000 2
10: params 0000000004000000 2
11: bootfiles 0000000020000000 2
12: data ffffffffffffffff 4
eMMC/TSD partition table have been checked OK!
check pattern success
mmc env offset: 0x27400000
In: serial
Out: serial
Err: serial
board id is : 7
hpd_state=0
cvbs performance type = 7, table = 1
[store]To run cmd[emmc dtb_read 0x1000000 0x40000]
_verify_dtb_checksum()-924: calc afb2eba9, store afb2eba9
_verify_dtb_checksum()-924: calc afb2eba9, store afb2eba9
dtb_read()-1046: total valid 2
dtb_read()-1113: do nothing
Amlogic multi-dtb tool
GZIP format, decompress...
Multi dtb detected
unified board, board id = 7
Multi dtb tool version: v2 .
Support 10 dtbs.
aml_dt soc: gxlx platform: p261 variant: 1g
dtb 0 soc: gxbb plat: p201 vari: 1g
dtb 1 soc: gxbb plat: p201 vari: 2g
dtb 2 soc: gxl plat: p211 vari: 1g
dtb 3 soc: gxl plat: p211 vari: 2g
dtb 4 soc: gxl plat: p215 vari: 1g
dtb 5 soc: gxl plat: p215 vari: 2g
dtb 6 soc: gxlx plat: p261 vari: 1g
dtb 7 soc: gxlx plat: p261 vari: 2g
dtb 8 soc: gxlx plat: p265 vari: 1g
dtb 9 soc: gxlx plat: p265 vari: 2g
Find match dtb: 6
wipe_data=successfulSecd
wipe_cache=successful
bmp pixel: 24
[OSD]load fb addr from dts
[OSD]fb_addr for logo: 0x3dc00000
[OSD]load fb addr from dts
[OSD]fb_addr for logo: 0x3dc00000
[CANVAS]addr=0x3dc00000 width=5760, height=2160
upgrade_step=2
amlkey_init() enter!
[EFUSE_MSG]keynum is 4
[BL31]: tee size: 0
[KM]Error:f[key_manage_query_size]L507:key[deviceid] not programed yet
key1 = 23dc4cb3
key2 = 6996c43b
key3 = 23dcdd22
time_out = 7a120
ir init
irkey - irkey key_value1 key_value2 key_value3 time_value
Usage:
irkey
rebootmode=cold_boot
Enter USB burn
Try connect time out 701, 700, 1746
Hit any key to stop autoboot: 0
ee_gate_off ...
## Booting Android Image at 0x01080000 ...
reloc_addr =33efb7e0
copy done
Amlogic multi-dtb tool
Single dtb detected
load dtb from 0x1000000 ......
Uncompressing Kernel Image ... OK
kernel loaded at 0x01080000, end = 0x02045bd0
Loading Ramdisk to 33e02000, end 33edd0ac ... OK
Loading Device Tree to 000000000fff3000, end 000000000ffffb14 ... OK
signature:
fdt_instaboot: get header err
Starting kernel ...
uboot time: 4726981 us
[ 0.000000@0] Initializing cgroup subsys cpu
[ 0.000000@0] Initializing cgroup subsys cpuacct
[ 0.000000@0] Linux version 3.14.29-g8692ef4-dirty (root@hisense-vpc) (gcc version 4.9.2 20140904 (prerelease) (crosstool-NG linaro-1.13.1-4.9-2014.09 - Linaro GCC 4.9-2014.09) ) #1 SMP PREEMPT Thu Oct 15 15:26:43 CST 2020
[ 0.000000@0] CPU: ARMv71 Processor [410fd034] revision 4
[ 0.000000@0] bootconsole [earlycon0] enabled
get_dvfs_info 0007
INFO: HDCP22 key read fail!
INFO: p1d 0
INFO: pd1 0
|
網(wǎng)站導航
樓主: hao501802766
[復(fù)制鏈接]
發(fā)表于 2022-6-5 11:08
znds.com 