|
|
求助反饋
| 品牌: |
中興 |
| 型號: |
ZXV10 B860AV1.1 |
| QQ: |
176170319 |
| 問題描述: |
破解中出現以下問題，不能輸代碼，求解 |
| 拍照上傳圖片: |
- |
本帖最后由 山陰路的夏天 于 2018-2-1 14:06 編輯
AC_ON
MIU0_DQS-OK
BIST0-???
MIU0-1024_U
Start uboot
Relocation Offset is: 015d7000
[AT][MB][start ub][475]
U-Boot 2011.06-00120-g7a77291-dirty (Jan 02 2018 - 22:29:27)
[MIU INFO] miu opencreate instance at 54ee9418 with private size 80 bytes at 54e e9460
create instance at 54ee94b8 with private size 52 bytes at 54ee9500
uboot held at [54cddf60~56000000],size=013220a0
CPU : Clippers
Board: BD_MST207C_D01A_S_CLIPPERS
DRAM: 864 MiB
Now running in RAM - U-Boot at: 55100000
eMMC: HS200 200MHz
eMMC 7.28 GB [E8FFF8h]
In: serial
Out: serial
Err: serial
Net: zte_shutdow =false
No ethernet found.
Set MAC default
MAC: 0x0: 0x30: 0x1b: 0xba:0x2: 0xdb
msIR_Initialize
[CPU INFO] cpu opencreate instance at 54ef99c0 with private size 44 bytes at 54e f9a08
CPUIoctl - MDrv_CMD_CPU_QueryClock
[UTOPIA INFO] close moduleNames[38]: MODULE_CPU
[AT][MBoot][Driver Init][732]
### main_loop entered: s is true
### main_loop entered: bootdelay=1
Starting logo
============= set bootargs ===============
[setup_com_controlenv] COMControlFlag=> value[1]=, val=0
zte_mac=74:97:81:5F:85:2D,ethaddr=74:97:81:5F:85:2D
Hit any key to stop autoboot: 1@
step1 error...
abort=0 0
mxy: MAEKET_IS_SDLT=0,MarketCode=32, OperatorsCode=3
do_bootcheck called
MMC_CAPACITY_512 =15269880
current emmc size is =0xe8fff8 (should by 512)
MMCusrdata_size =11773944
current userdata size =0xb3a7f8 (should by 512)
this is 8G emmc
get_boot1_ver cmd_boot1=mmc read.boot 1 0x25000000 0x0 0x200000
set hdmi hdcp mode 0!
Saving Environment to MMC...
Writing to MMC(0)... 128 blocks written: OK
128 blocks written: OK
done
iTVSTandard2Resolution = 2
value[29] = 534104162101344000007497815F852D
[setup_bootenv] COMControlFlag=> value[30]=, val=0
ethaddr =74:97:81:5F:85:2D
jy ....
search ....
waldo msIR_GetIRKeyCode line:483 breturn false
fore uup IRKey [0xff]
BootMode=0
search ....
waldo msIR_GetIRKeyCode line:483 breturn false
fore uup IRKey [0xff]
BootMode=0
search ....
waldo msIR_GetIRKeyCode line:483 breturn false
fore uup IRKey [0xff]
BootMode=0
search ....
waldo msIR_GetIRKeyCode line:483 breturn false
fore uup IRKey [0xff]
BootMode=0
search ....
waldo msIR_GetIRKeyCode line:483 breturn false
fore uup IRKey [0xff]
BootMode=0
search ....
waldo msIR_GetIRKeyCode line:483 breturn false
fore uup IRKey [0xff]
BootMode=0
search ....
waldo msIR_GetIRKeyCode line:483 breturn false
fore uup IRKey [0xff]
BootMode=0
search ....
waldo msIR_GetIRKeyCode line:483 breturn false
fore uup IRKey [0xff]
BootMode=0
search ....
waldo msIR_GetIRKeyCode line:483 breturn false
fore uup IRKey [0xff]
BootMode=0
search ....
waldo msIR_GetIRKeyCode line:483 breturn false
fore uup IRKey [0xff]
BootMode=0
[ztebsp] BootMode=0
[do_bootcheck,1204][ZTEWatchdog]PATCH FOR zte BEGIN
[do_bootcheck,1208][ZTEWatchdog] Watchdog_enable TRUE
[do_bootcheck,1214][ZTEWatchdog] Watchdog start, MAXTIME 120
create instance at 54ef9bb0 with private size 256 bytes at 54ef9bf8
MDrv_PNL_Init u32PnlRiuBaseAddr = 1f200000
MDrv_PNL_Init u32PMRiuBaseAddr = 1f000000
PNL:[MDrv_PNL_SetPanelType][613]
[_MDrv_PNL_Init_LPLL][323]pstPanelInitData->u16Width=1280, pstPanelInitData->u16 Height=720
[_MDrv_PNL_Init_LPLL][325]u16HTotal=1980,u16VTotal=750,pstPanelInitData->u16HTot al=1980,pstPanelInitData->u16VTotal=750, u16DefaultVFreq=500
[_MDrv_PNL_Init_Output_Dclk][369]pstPanelInitData->u16Width=1280, pstPanelInitDa ta->u16Height=720
[_MDrv_PNL_Init_Output_Dclk][371]u16HTotal=1980,u16VTotal=750,pstPanelInitData-> u16HTotal=1980,pstPanelInitData->u16VTotal=750, u16DefaultVFreq=500
PNL:CalculateLPLLSETbyDClk u32KHz = 742500000, u64DefaultLdHz = 742500000
PNL:CalculateLPLLSETbyDClk u32LpllSet = 3531df
[MApi_XC_MLG_GetStatus, 1603]No instance existed, please get an instance by call ing MApi_XC_Init() first
msHdmitx_Disp_Init
create instance at 54ef9d00 with private size 1720 bytes at 54ef9d48
[XC,Version]
no need to patchcreate instance at 54efa948 with private size 80 bytes at 54efa 990
Rx Support HDMI mode!
setHDMITxAnalogTuning: Error: MApi_HDMITx_GetRxDCInfoFromEDID EDID is not ready, at 262
shift -8 pixels in PAL mode
Create Dolby single part name task failed!![Hal_VE_Set_PreHSD][1826] ERROR!!! HV SD H input = 0, HVSD H output = 720
[Hal_VE_Set_PreVSD][2002] ERROR!!! HVSD V input = 0, HVSD V output = 576
[Hal_VE_EnableDI][2110] bEnable = 0, bIsDNR2VE = 0
lyndon Hal_VE_Set_PreVSD 1mmc change mount : tvcustomer
Size of file "/720.jpg" from mmc device 0 partition tvcustomer: 473547 bytes
Loading file "/720.jpg" at offset 0x0 from mmc device 0 partition tvcustomer
473547 bytes read
create instance at 54efa9e8 with private size 304 bytes at 54efaa30
[AT][MB][JPD Decode][2530]
[UTOPIA INFO] close moduleNames[35]: MODULE_NJPEG_EX
create instance at 54efa9e8 with private size 132280 bytes at 54efaa30
[GOP INFO] gop opencreate instance at 54f1aef0 with private size 6908 bytes at 5 4f1af38
[AT][MB][Show Logo][2581]
mxy--> ir_recovery is 0
mxy: ir_recovery is 0...
## Booting kernel from Legacy Image at 25000800 ...
Image Name: MStar-linux
Image Type: ARM Linux Multi-File Image (uncompressed)
Data Size: 5317739 Bytes = 5.1 MiB
Load Address: 20208000
Entry Point: 20208000
Contents:
Image 0: 4627400 Bytes = 4.4 MiB
Image 1: 690327 Bytes = 674.1 KiB
## Loading init Ramdisk from multi component Legacy Image at 25000800 ...
-usb_stop(USB_PORT0)
-usb_stop(USB_PORT1)
-usb_stop(USB_PORT2)
Loading Multi-File Image ... OK
[AT][MB][start kr][2827]
Starting kernel ...
[PROTECT ERROR], not expected dram size: 0x0
#######################################################################
# [PROTECT WARNING], miu kernel protect is not enabled on second dram #
#######################################################################
Uncompressing Linux... done, booting the kernel.
KERN-3.10.23.001049551
tommy: thread_info_cache_init
mtdoops: mtd device (mtddev=name/number) must be supplied
[drivers/mstar2/drv/emac/mdrv_emac.c MDev_EMAC_HW_init 2196] ready init mutex
[drivers/mstar2/drv/emac/mdrv_emac.c MDev_EMAC_HW_init 2197] after init mutex
RBQP_BASE = 51604000
init: /init.clippers.rc: 455: ignored duplicate definition of service 'mdnsd'
init: /zte_init.rc: 32: ignored duplicate definition of service 'IptvQosServ'
init: /zte_init.rc: 38: ignored duplicate definition of service 'xiriservice'
init: /zte_init.rc: 48: ignored duplicate definition of service 'softdetector'
init: ## ProductID: strlen (32)!
healthd: No charger supplies found
init: cannot find '/system/bin/xiriservice_ChinaMobile_SiChuan', disabling 'blue toothd'
init: cannot find '/system/bin/bleservice', disabling 'bleservice'
init: cannot find '/data/data/com.android.smart.terminal.dplatform/bin/IptvQosSe rv', disabling 'IptvQosServ'
init: cannot find '/system/bin/stratky.sh', disabling 'stratky'
|
上一篇： ZTE ZXVB680AV1.1 刷機失敗下一篇： 前幾天系統更新后無法使用當貝市場 格式化重新刷機以后t...
|
網站導航
發表于 2018-2-1 13:47
收藏
淘帖
頂一個
踩
提升卡
置頂卡
變色卡
千斤頂
樓主
znds.com 