以此教程:http://gotdoctom.com/jc/article/13991
USB/TTL連接：安裝不了？？？？？？
GXL:BL1:9ac50e:a1974b;FEAT:ADFC318C;POC:3;RCY:0;EMMC:0;READ:0;0.0;CHK:0;
TE: 113896
BL2 Built : 01:56:32, Dec 22 2016.
gxl g1614c0b - xiaobo.gu@droid05
Board ID = 7, adc=514
set vcck to 1070 mv
set vddee to 1070 mv
CPU clk: 1200MHz
2layers board, use ddr_set[0]
DQS-corr enabled
DDR scramble enabled
DDR3 chl: Rank0+1 @ 792MHz - FAIL
DDR3 chl: Rank0 @ 792MHz - PASS
Rank0: 1024MB(auto)-2T-11
DataBus test pass!
AddrBus test pass!
-s
Load fip header from eMMC, src: 0x0000c200, des: 0x01400000, size: 0x00004000
New fip structure!
Load bl30 from eMMC, src: 0x00010200, des: 0x01100000, size: 0x00007400
Load bl301 from eMMC, src: 0x00018200, des: 0x01200000, size: 0x00002200
Load bl31 from eMMC, src: 0x0001c200, des: 0x10100000, size: 0x00019400
Load bl33 from eMMC, src: 0x00038200, des: 0x01000000, size: 0x00086400
NOTICE: BL3-1: v1.0(debug):959fdf0
NOTICE: BL3-1: Built : 15:01:44, Dec 29 2016
aml log : bl31 normal boot !
[Image: gxl_v1.1.3089-661026e 2017-01-10 18:34:56 qiufang.dai@droid07]
bl30: check_permit, count is 1
bl30: check_permit: ok!
chipid: ef be ad de d f0 ad ba ef be ad de not ES chip
efuse init ops = e2
efuse init hdcp = c, cf9=7
[0.543696 Inits done]
sINFeOc:u r e tBaLs3k- 1s:t aIrnti!ti
alizing runtihmieg hs etrvices
WARNING: No OPTEE provided by BL2 boot loader
ERROR: Error initializing runtime service opteed_fast
INFO: BL3-1: Preparing for EL3 exit to normal world
INFO: BL3-1: Next image address = 0x1000000
INFO: BL3-1: Next image spsr = 0x3c9
U-Boot 2015.01-gcae2519-dirty (Feb 12 2017 - 15:46:08)
DRAM: 1 GiB
Relocation Offset is: 36eec000
gpio: pin GPIODV_24 (gpio 43) value is 1
mwm 0xc8837004:[0x aa203] with [0x ea203] ok
mwm 0xc883700c:[0x 3e3b744] with [0x 3e3b764] ok
mwm 0xc8837010:[0x c0101] with [0x c8101] ok
mwm 0xc8837010:[0x c8101] with [0x 128101] ok
register usb cfg[0][1] = 0000000037f61090
[CANVAS]canvas init
vpu: error: vpu: check dts: FDT_ERR_BADMAGIC, load default parameters
vpu: clk_level = 7
vpu: set clk: 666667000Hz, readback: 666660000Hz(0x300)
vpp: vpp_init
MMC: aml_priv->desc_buf = 0x0000000033edcac0
aml_priv->desc_buf = 0x0000000033edede0
SDIO Port B: 0, SDIO Port C: 1
emmc/sd response timeout, cmd8, status=0x3ff2800
emmc/sd response timeout, cmd55, status=0x3ff2800
[mmc_init] mmc init success
mmc read lba=0x14000, blocks=0x400
Amlogic multi-dtb tool
Multi dtb detected
2layers board, board id use 7
Multi dtb tool version: v2 .
Support 6 dtbs.
aml_dt soc: gxl platform: p211 variant: 1g
dtb 0 soc: gxbb plat: p201 vari: 1g
dtb 1 soc: gxbb plat: p201 vari: 2g
dtb 2 soc: gxl plat: p211 vari: 1g
dtb 3 soc: gxl plat: p211 vari: 2g
dtb 4 soc: gxl plat: p215 vari: 1g
dtb 5 soc: gxl plat: p215 vari: 2g
Find match dtb: 2
start dts,buffer=0000000033ee1630,dt_addr=0000000033ef2e30
parts: 13
00: logo 0000000002000000 1
01: recovery 0000000002000000 1
02: rsv 0000000000800000 1
03: tee 0000000000800000 1
04: crypt 0000000002000000 1
05: misc 0000000002000000 1
06: instaboot 0000000020000000 1
07: boot 0000000002000000 1
08: system 0000000040000000 1
09: cache 0000000020000000 2
10: params 0000000004000000 2
11: bootfiles 0000000020000000 2
12: data ffffffffffffffff 4
get_dtb_struct: Get emmc dtb OK!
overide_emmc_partition_table: overide cache
[mmc_get_partition_table] skip partition cache.
Partition table get from SPL is :
name offset size flag
================================================================================ ===
0: bootloader 0 400000 0
1: reserved 2400000 4000000 0
2: cache 6c00000 20000000 2
3: env 27400000 800000 0
4: logo 28400000 2000000 1
5: recovery 2ac00000 2000000 1
6: rsv 2d400000 800000 1
7: tee 2e400000 800000 1
8: crypt 2f400000 2000000 1
9: misc 31c00000 2000000 1
10: instaboot 34400000 20000000 1
11: boot 54c00000 2000000 1
12: system 57400000 40000000 1
13: params 97c00000 4000000 2
14: bootfiles 9c400000 20000000 2
15: data bcc00000 115400000 4
mmc read lba=0x12000, blocks=0x2
mmc read lba=0x12002, blocks=0x2
mmc_read_partition_tbl: mmc read partition OK!
eMMC/TSD partition table have been checked OK!
mmc env offset: 0x27400000
In: serial
Out: serial
Err: serial
board id is : 7
hpd_state=1
[720p60hz] is invalid for cvbs.
set hdmitx VIC = 4
config HPLL = 2970
HPLL: 0xc000027b
config HPLL done
j = 2 vid_clk_div = 1
hdmitx: set enc for VIC: 4
HDMITX-DWC addr=0x10004006 rd_data=0x40
Error: HDMITX-DWC exp_data=0xff mask=0x9f
enc_vpu_bridge_reset[1188]
hdmitx phy setting done
div40 = 0
[store]To run cmd[emmc dtb_read 0x1000000 0x40000]
read emmc dtb
Amlogic multi-dtb tool
Multi dtb detected
Multi dtb tool version: v2 .
Support 6 dtbs.
aml_dt soc: gxl platform: p211 variant: 1g
dtb 0 soc: gxbb plat: p201 vari: 1g
dtb 1 soc: gxbb plat: p201 vari: 2g
dtb 2 soc: gxl plat: p211 vari: 1g
dtb 3 soc: gxl plat: p211 vari: 2g
dtb 4 soc: gxl plat: p215 vari: 1g
dtb 5 soc: gxl plat: p215 vari: 2g
Find match dtb: 2
Net: dwmac.c9410000
wipe_data=successfulSecd
wipe_cache=successful
bmp pixel: 16
[CANVAS]addr=0x3d800000 width=2560, height=1440
upgrade_step=2
amlkey_init() enter!
[EFUSE_MSG]keynum is 4
[BL31]: tee size: 0
[KM]Error:f[key_manage_query_size]L507:key[deviceid] not programed yet
gpio: pin GPIOAO_2 (gpio 102) value is 1
rebootmode=cold_boot
Hit any key to stop autoboot: 0
ee_gate_off ...
## Booting Android Image at 0x01080000 ...
reloc_addr =33f09250
copy done
Amlogic multi-dtb tool
Single dtb detected
load dtb from 0x1000000 ......
Uncompressing Kernel Image ... OK
kernel loaded at 0x01080000, end = 0x01f57020
Loading Ramdisk to 33c6c000, end 33ed9b21 ... OK
Loading Device Tree to 000000001fff3000, end 000000001ffff41a ... OK
signature:
fdt_instaboot: get header err
Starting kernel ...
uboot time: 2142576 us
[ 0.000000@0] Initializing cgroup subsys cpu
[ 0.000000@0] Initializing cgroup subsys cpuacct
[ 0.000000@0] Linux version 3.14.29-svn662 (hej@gci2017-Super-Server) (gcc ve rsion 4.9.2 20140904 (prerelease) (crosstool-NG linaro-1.13.1-4.9-2014.09 - Lina ro GCC 4.9-2014.09) ) #1 SMP PREEMPT Fri Jan 19 01:20:29 CST 2018
[ 0.000000@0] CPU: armv71 Processor [410fd034] revision 4
[ 0.000000@0] bootconsole [earlycon0] enabled
get_dvfs_info 0007
INFO: HDCP22 key read fail!
INFO: p1d 0
INFO: pd1 0
root@p201_iptv:/ # start adbd
root@p201_iptv:/ # df
Filesystem Size Used Free Blksize
/dev 425.8M 128.0K 425.7M 4096
/sys/fs/cgroup 425.8M 12.0K 425.8M 4096
/mnt/asec 425.8M 0.0K 425.8M 4096
/mnt/obb 425.8M 0.0K 425.8M 4096
/tmp 425.8M 1.8M 424.0M 4096
/tmp/playInfoLog 425.8M 0.0K 425.8M 4096
/tmp/capture 425.8M 0.0K 425.8M 4096
/tmp/begininfo 425.8M 0.0K 425.8M 4096
/tmp/collectinfo 425.8M 0.0K 425.8M 4096
/tmp/picinfo 425.8M 0.0K 425.8M 4096
/storage/external_storage 425.8M 0.0K 425.8M 4096
/system 991.9M 431.8M 560.1M 4096
/data 4.2G 151.0M 4.0G 4096
/cache 495.9M 644.0K 495.3M 4096
/params 59.0M 40.0K 58.9M 4096
/bootfiles 495.9M 384.0K 495.6M 4096
/mnt/shell/emulated 4.1G 151.0M 4.0G 4096
/swap_zram0 484.3M 20.0K 484.3M 4096
/storage/external_storage/sda1 1.9G 520.6M 1.4G 4096
root@p201_iptv:/ # cd /storage/external_storage/sda1
root@p201_iptv:/storage/external_storage/sda1 # ls
Android
dbsc.apk
dbzm.apk
root@p201_iptv:/storage/external_storage/sda1 # pm install dbsc.apk
pkg: dbsc.apk
apks is not valid!
root@p201_iptv:/storage/external_storage/sda1 # pm install dbzm.apk
pkg: dbzm.apk
apks is not valid!
安裝不了？？？？？？？？？？？？？？？ |
網(wǎng)站導(dǎo)航
發(fā)表于 2018-3-19 19:41
收藏
淘帖
頂一個(gè)
踩
提升卡
置頂卡
變色卡
千斤頂
樓主
znds.com 