8726mx命令怎么使用

xhm789 · 發表于 2021-3-30 19:26

本帖最后由 xhm789 于 2021-3-30 20:05 編輯

電視進不了桌面，想重u盤裝。

EC3_MX_PANEL_V6 #?

? - alias for 'help'

adtask - Ad task when time is not boot time it will sleep

aeschk - aeschk AES aLGorithm check sub-system

autoping- do auto ping test

autoscr - run script from memory

base - print or set address offset

bdinfo - print Board Info structure

bmp - manipulate BMP image data

boardid_prefetch- boardid sub-system

boot - SPI-NAND-COMPATIBLE

bootc - boot boot.img form sdcard

bootm - boot application image from memory

bootn - boot uImage form nand

bootp - boot image via network using BOOTP/TFTP protocol

bootr - boot uImage_recovery from sdcard

bootu - boot uImage form sdcard

burnuboot- burn uboot form sdcard

calc - command for calculate

cbusreg - cbus register read/write

chpart - change active partition

clear_rebootmode- clear rebootmode

clkmsr - measure PLL clock

cmp - memory compare

coninfo - print console devices and information

cp - memory copy

crc32 - checksum calculation

data - SPI-NAND-COMPATIBLE || SPI-NAND-EMMC-COMPATIBLE

dcache - enable or disable data cache

defenv - default environment

defenv_without- defenv without environment variables

dhcp - boot image via network using DHCP/TFTP protocol

dummy - Customer defined command!

echo - echo args to console

editenv - edit environment variable

efuse - efuse version/licence/mac/hdcp/usid read/write or dump raw efuse data commands

env - environment handling commands

ethchk - check ethernet status

ethdbg - set ethernet debug level

ethmode - set ethernet mac mode

ethrst - reset ethernet phy

exit - exit script

ext2load- load binary file from a Ext2 filesystem

ext2ls - list files in a directory (default /)

false - do nothing, unsuccessfully

fatexist- find the file from a dos filesystem

fatinfo - print information about filesystem

fatload - load binary file from a dos filesystem

fatls - list files in a directory (default /)

get_img_size- get img size and save the result as a environment variable

get_rebootmode- get reboot mode

go - start application at address 'addr'

hdcp - HDCP sub-system

help - print command description/usage

icache - enable or disable instruction cache

imxtract- extract a part of a multi-image

init_wifi- init wifi power

irkey - irkey key_value time_value

itest - return true/false on integer compare

kgdb - enter gdb remote debug mode

ledflicker- Led flicker when there is no uImage or recovery can run

loadb - load binary file over serial line (kermit mode)

loadenv - load environment at address 'addr'

loads - load S-Record file over serial line

loadx - load binary file over serial line (xmodem mode)

loady - load binary file over serial line (ymodem mode)

loop - infinite loop on address range

macreg - ethernet mac register read/write/dump

md - memory display

mdc_clk - do mdc clock

mm - memory modify (auto-incrementing address)

mmc - MMC sub system

mmcinfo - display MMC info

msleep - delay execution for some time

mtdparts- define flash/nand partitions

mtest - simple RAM read/write test

mw - memory write (fill)

nand - NAND sub-system

nboot - boot from NAND device

netspd_f- enforce eth speed

nm - memory modify (constant address)

phyreg - ethernet phy register read/write/dump

ping - send ICMP ECHO_REQUEST to network host

printenv- print environment variables

rarpboot- boot image via network using RARP/TFTP protocol

reset - Perform RESET of the CPU

run - run commands in an environment variable

saradc - saradc sub-system

saveenv - save environment variables to persistent storage

secukey - security KEY sub-system

setenv - set environment variables

sf - SPI flash sub-system

showvar - print local hushshell variables

sleep - delay execution for some time

source - run script from memory

ssecukey- NAND KEY sub-system

test - minimal test like /bin/sh

tftpboot- boot image via network using TFTP protocol

tiny_usbtool- start tiny USB tool for PC burner

true - do nothing, successfully

unpackimg- unpack imgpack to single

usb - USB sub-system

usbbc - test usb bc

usbboot - boot from USB device

usid_prefetch- usid sub-system

uuid_prefetch- uuid sub-system

version - print monitor, compiler and linker version

video - video sub-system

xhm789 · 發表于 2021-3-30 20:03

EC3_MX_PANEL_V6 #?
?    - alias for 'help'
adtask  - Ad task when time is not boot time it will sleep
aeschk  - aeschk AES algorithm check sub-system
autoping- do auto ping test
autoscr - run script from memory
base - print or set address offset
bdinfo  - print Board Info structure
bmp    - manipulate BMP image data
boardid_prefetch- boardid sub-system
boot - SPI-NAND-COMPATIBLE
bootc - boot boot.img form sdcard
bootm - boot application image from memory
bootn - boot uImage form nand
bootp - boot image via network using BOOTP/TFTP protocol
bootr - boot uImage_recovery from sdcard
bootu - boot uImage form sdcard
burnuboot- burn uboot form sdcard
calc - command for calculate
cbusreg - cbus register read/write
chpart  - change active partition
clear_rebootmode- clear rebootmode
clkmsr  - measure PLL clock
cmp    - memory compare
coninfo - print console devices and information
cp    - memory copy
crc32 - checksum calculation
data - SPI-NAND-COMPATIBLE || SPI-NAND-EMMC-COMPATIBLE
dcache  - enable or disable data cache
defenv  - default environment
defenv_without- defenv without environment variables
dhcp - boot image via network using DHCP/TFTP protocol
dummy - Customer defined command!
echo - echo args to console
editenv - edit environment variable
efuse - efuse version/licence/mac/hdcp/usid read/write or dump raw efuse data commands
env    - environment handling commands
ethchk  - check ethernet status
ethdbg  - set ethernet debug level
ethmode - set ethernet mac mode
ethrst  - reset ethernet phy
exit - exit script
ext2load- load binary file from a Ext2 filesystem
ext2ls  - list files in a directory (default /)
false - do nothing, unsuccessfully
fatexist- find the file from a dos filesystem
fatinfo - print information about filesystem
fatload - load binary file from a dos filesystem
fatls - list files in a directory (default /)
get_img_size- get img size and save the result as a environment variable
get_rebootmode- get reboot mode
go    - start application at address 'addr'
hdcp - HDCP sub-system
help - print command description/usage
icache  - enable or disable instruction cache
imxtract- extract a part of a multi-image
init_wifi- init wifi power
irkey - irkey key_value time_value
itest - return true/false on integer compare
kgdb - enter gdb remote debug mode
ledflicker- Led flicker when there is no uImage or recovery can run
loadb - load binary file over serial line (kermit mode)
loadenv - load environment at address 'addr'
loads - load S-Record file over serial line
loadx - load binary file over serial line (xmodem mode)
loady - load binary file over serial line (ymodem mode)
loop - infinite loop on address range
macreg  - ethernet mac register read/write/dump
md    - memory display
mdc_clk - do mdc clock
mm    - memory modify (auto-incrementing address)
mmc    - MMC sub system
mmcinfo - display MMC info
msleep  - delay execution for some time
mtdparts- define flash/nand partitions
mtest - simple RAM read/write test
mw    - memory write (fill)
nand - NAND sub-system
nboot - boot from NAND device
netspd_f- enforce eth speed
nm    - memory modify (constant address)
phyreg  - ethernet phy register read/write/dump
ping - send ICMP ECHO_REQUEST to network host
printenv- print environment variables
rarpboot- boot image via network using RARP/TFTP protocol
reset - Perform RESET of the CPU
run    - run commands in an environment variable
saradc  - saradc sub-system
saveenv - save environment variables to persistent storage
secukey - security KEY sub-system
setenv  - set environment variables
sf    - SPI flash sub-system
showvar - print local hushshell variables
sleep - delay execution for some time
source  - run script from memory
ssecukey- NAND KEY sub-system
test - minimal test like /bin/sh
tftpboot- boot image via network using TFTP protocol
tiny_usbtool- start tiny USB tool for PC burner
true - do nothing, successfully
unpackimg- unpack imgpack to single
usb    - USB sub-system
usbbc - test usb bc
usbboot - boot from USB device
usid_prefetch- usid sub-system
uuid_prefetch- uuid sub-system
version - print monitor, compiler and linker version
video - video sub-system

xhm789 · 發表于 2021-3-30 20:04

EC3_MX_PANEL_V6 #?
?    - alias for 'help'
adtask  - Ad task when time is not boot time it will sleep
aeschk  - aeschk AES algorithm check sub-system
autoping- do auto ping test
autoscr - run script from memory
base - print or set address offset
bdinfo  - print Board Info structure
bmp    - manipulate BMP image data
boardid_prefetch- boardid sub-system
boot - SPI-NAND-COMPATIBLE
bootc - boot boot.img form sdcard
bootm - boot application image from memory
bootn - boot uImage form nand
bootp - boot image via network using BOOTP/TFTP protocol
bootr - boot uImage_recovery from sdcard
bootu - boot uImage form sdcard
burnuboot- burn uboot form sdcard
calc - command for calculate
cbusreg - cbus register read/write
chpart  - change active partition
clear_rebootmode- clear rebootmode
clkmsr  - measure PLL clock
cmp    - memory compare
coninfo - print console devices and information
cp    - memory copy
crc32 - checksum calculation
data - SPI-NAND-COMPATIBLE || SPI-NAND-EMMC-COMPATIBLE
dcache  - enable or disable data cache
defenv  - default environment
defenv_without- defenv without environment variables
dhcp - boot image via network using DHCP/TFTP protocol
dummy - Customer defined command!
echo - echo args to console
editenv - edit environment variable
efuse - efuse version/licence/mac/hdcp/usid read/write or dump raw efuse data commands
env    - environment handling commands
ethchk  - check ethernet status
ethdbg  - set ethernet debug level
ethmode - set ethernet mac mode
ethrst  - reset ethernet phy
exit - exit script
ext2load- load binary file from a Ext2 filesystem
ext2ls  - list files in a directory (default /)
false - do nothing, unsuccessfully
fatexist- find the file from a dos filesystem
fatinfo - print information about filesystem
fatload - load binary file from a dos filesystem
fatls - list files in a directory (default /)
get_img_size- get img size and save the result as a environment variable
get_rebootmode- get reboot mode
go    - start application at address 'addr'
hdcp - HDCP sub-system
help - print command description/usage
icache  - enable or disable instruction cache
imxtract- extract a part of a multi-image
init_wifi- init wifi power
irkey - irkey key_value time_value
itest - return true/false on integer compare
kgdb - enter gdb remote debug mode
ledflicker- Led flicker when there is no uImage or recovery can run
loadb - load binary file over serial line (kermit mode)
loadenv - load environment at address 'addr'
loads - load S-Record file over serial line
loadx - load binary file over serial line (xmodem mode)
loady - load binary file over serial line (ymodem mode)
loop - infinite loop on address range
macreg  - ethernet mac register read/write/dump
md    - memory display
mdc_clk - do mdc clock
mm    - memory modify (auto-incrementing address)
mmc    - MMC sub system
mmcinfo - display MMC info
msleep  - delay execution for some time
mtdparts- define flash/nand partitions
mtest - simple RAM read/write test
mw    - memory write (fill)
nand - NAND sub-system
nboot - boot from NAND device
netspd_f- enforce eth speed
nm    - memory modify (constant address)
phyreg  - ethernet phy register read/write/dump
ping - send ICMP ECHO_REQUEST to network host
printenv- print environment variables
rarpboot- boot image via network using RARP/TFTP protocol
reset - Perform RESET of the CPU
run    - run commands in an environment variable
saradc  - saradc sub-system
saveenv - save environment variables to persistent storage
secukey - security KEY sub-system
setenv  - set environment variables
sf    - SPI flash sub-system
showvar - print local hushshell variables
sleep - delay execution for some time
source  - run script from memory
ssecukey- NAND KEY sub-system
test - minimal test like /bin/sh
tftpboot- boot image via network using TFTP protocol
tiny_usbtool- start tiny USB tool for PC burner
true - do nothing, successfully
unpackimg- unpack imgpack to single
usb    - USB sub-system
usbbc - test usb bc
usbboot - boot from USB device
usid_prefetch- usid sub-system
uuid_prefetch- uuid sub-system
version - print monitor, compiler and linker version
video - video sub-system

› 你問我答 / 玩機教程 / 固件 › ZNDS刷機/救磚

8726mx命令怎么使用

8726mx命令怎么使用