河南CM311-5 ZG 2+16G
Reg Version: v1.0.5h
Reg Name: gk6323v100crbb_gk6323v100c_LPDDR4-2133_2GB_32bitx1_2layers_230317.reg
開始耍的雙系統 后來到期 不能自動進當貝桌面 就說刷一下 最開始招的卡刷 但是進不去adb 然后就找了很多包去刷
結果各種卡在如圖 后期刷成功也進不去系統 再后來就Failed to download fastboot!
QQ圖片20240312120528.png (216.49 KB, 下載次數: 9)
下載附件
保存到相冊
2024-3-16 01:54 上傳
串口已經連接，請給單板上電，若已經上電，請斷電后重新上電。
Bootrom start
Boot Media: eMMC (Default Speed)
##############################################
Decrypt auxiliary code ...OK
############################################################# ---- 9%
########################################################################################################### ---- 19%
########################################################################################################### ---- 29%
########################################################################################################### ---- 39%
########################################################################################################### ---- 49%
########################################################################################################### ---- 59%
########################################################################################################### ---- 69%
########################################################################################################### ---- 79%
########################################################################################################### ---- 89%
########################################################################################################### ---- 100%
Enter boot auxiliary code
Reg Version: v1.0.5h
Reg Name: gk6323v100crbb_gk6323v100c_LPDDR4-2133_2GB_32bitx1_2layers_230317.reg
DDR HW training...
DDR SW training...
Boot auxiliary code success
Bootrom success
System startup
Relocate Boot
Jump to C code
Compressed-boot v1.0.0
Uncompress..........................Ok
System startup
Relocate Boot
Jump to C code
U-Boot 2019.07 (Jun 08 2023 - 15:51:40 +0800)
DRAM: TLB ADDR:0x4000
2 GiB
CPU: GK6323V100C ()
Boot Media:eMMC
DDR Size: 2 GiB (Boot: 2 GiB)
WARNING: Caches not enabled
MMC: scan edges:2 p2f:5 f2p:7
mix set temp-phase 2
scan elemnts: startp:106 endp:98
Tuning SampleClock. mix set phase:[02/07] ele:[06/16]
MMC/SD Card:
MID: 0xf4
Read Block: 512 Bytes
Write Block: 512 Bytes
Chip Size: 14912M Bytes (High Capacity)
Name: "Biwin "
Chip Type: MMC
Version: 1.0
Speed: 100000000Hz
Mode: HS400
Voltage: 1.8V
Bus Width: 8bit
Boot Addr: 0 Bytes
Loading Environment from MMC... OK
Fast logo
Net: up
Warning: up (eth0) using random MAC address - 2e:ac:ed:e3:b9:3e
SDK Version: GKSTBAndroidV300R002C00SPC023_v2022102516
check remote recovery button begin
check_remote_recovery,ret:-1
__recovery__into no IR KEY
count=2
mac format correct
mac:AC:56:7B:2D:2E:28
Reserve Memory
Start Addr: 0x7FFFE000
Bound Addr: 0x1511E000
Free Addr: 0x7F67F000
Alloc Block: Addr Size
0x78FD000 0x2000
0x7FFFC000 0x1000
0x7FFF9000 0x2000
0x7FEA6000 0x152000
0x7F6BC000 0x7E9000
0x7F6BA000 0x1000
0x7F6B0000 0x9000
0x7F67F000 0x30000
Autobooting in 0 seconds, Press Ctrl+C to stop autoboot
get env = <NULL>
MMC read: dev # 0, block # 65536, count 4096 ... 4096 blocks read: OK
137391616 Bytes/s
MMC read: dev # 0, block # 229376, count 30720 ... 30720 blocks read: OK
153312256 Bytes/s
## Booting kernel from Legacy Image at 01ffffc0 ...
Image Name: Linux-4.9.118_gk6323v100c
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 11521081 Bytes = 11 MiB
Load Address: 02000000
Entry Point: 02000000
XIP Kernel Image ... OK
ATAGS [0x00000100 - 0x0000074C], 1612Bytes
Starting kernel ...
Start ATF with aarch32 kernel...
bl33_ep->spsr = 0x1D3
Start Warm Reseting
INFO: BL31 Early setup
NOTICE: BL31: v2.0(debug):b05835d-dirty
NOTICE: BL31: Built : 13:49:58, Aug 20 2021
INFO: $$$$0x1 0x3
INFO: GICv3 without legacy support detected. ARM GICV3 driver initialized in EL3
INFO: BL31: Initializing runtime services
WARNING: No TSP provided by BL2 boot loader, Booting device without TSP initialization. SMC`s destined for TSP will return SMC_UNK
ERROR: Error initializing runtime service tspd_fast
INFO: BL31: Preparing for EL3 exit to normal world
INFO: Entry point address = 0x2000000
INFO: SPSR = 0x1d3
Uncompressing Linux... done, booting the kernel.
INFO: REG_PERI_CPU_AARCH_MODE:0xf8a80030 REG_PERI_A53_RVBARADDR:0xf8a80034
INFO: REG_PERI_CPU_AARCH_MODE:0xf8a80030 REG_PERI_A53_RVBARADDR:0xf8a80034
INFO: REG_PERI_CPU_AARCH_MODE:0xf8a80030 REG_PERI_A53_RVBARADDR:0xf8a80034
mmc0: error -110 whilst initialising MMC card
mmc0: error -110 whilst initialising MMC card
mmc0: error -110 whilst initialising MMC card
mmc0: error -110 whilst initialising MMC card
Failed to wait the boot to run.
The boot code uses the debug or release version, and the bootstrap burning function is disabled. When this problem occurs, select the programmer file for burning.
Failed to download fastboot!
|
網站導航
發表于 2024-3-16 01:54
收藏
淘帖
頂一個
踩
提升卡
置頂卡
變色卡
千斤頂
樓主
znds.com 